Eurodyne Tables

From Simos Wiki
Revision as of 03:26, 7 January 2021 by Aaronc7 (talk | contribs) (→‎Timing)
Jump to navigation Jump to search

Calibration tables

Limiters

Maximum Clutch Torque

The Maximum Clutch Torque tables are used to define the maximum available torque based on RPM and gear. The two tables represent MANUAL and DSG transmissions. The ECU will look at the current Driver requested torque percentage (input from the pedal), along with the current RPM to arrive at the target torque value.

The Max torque tables can be used to limit torque delivery in certain gears.

Boss maxclutchtorque.png

Fueling

Basic Lambda vs Airmass DI

This table is the part throttle fueling map. The ECU will target the entered lambda values during part throttle (not pedal position). At full throttle, the ECU will switch to the "Full Load Lambda" fueling table.

Note: "Full Throttle" can happen even if the accelerator pedal is not pushed completely down.

Full Load Lambda

This table is referenced when the ECU is in a full throttle situation. The X-Axis represents time elapsed in full load in seconds.

Lambda EGT Protection

This table determines the lambda target when the ECU determines EGT (exhaust gas temperature) is too high. You may consider using targets which are not as rich if you have an aftermarket DP.

Minimum Lambda Target

This is the absolute lowest lambda value that the ECU will target. The ECU will ignore any lower values in other fueling tables.

Boost

Maximum Turbo Pressure Ratio

This table is used to define the maximum turbo boost at a given RPM range. The ECU will not attempt to overshoot this boost value. Measurements are relative boost pressure *not* absolute pressure.

Maxturbopressureratio.png

Map for boost pressure actuator setpoint

More commonly known as... wastegate duty cycle (though it's the reverse).

Factory file

TBD

Is20 wgdc.png

Boss/Big turbo version

The Boss file uses a different strategy that's much more straightforward. To maintain X Boost at Y RPM open the gate Z percentage.

Boss wgdc.png

Timing

Ignition timing is determined by two look-up tables (Ignition timing, low octane and Ignition timing, high octane) and two settings tables (Min octane for adjustable features and Max octane for adjustable features). Within the Simos18 ECU there are additional lookup tables that will impact timing that Maestro does not access. Intake Air Temperature (IAT) as recorded by the MAP sensor is one such variable that will impact your timing advance. High IATs will retard timing to reduce the likelihood of pre-ignition due to high combustion temperatures within the cylinder. The ECU will override the two Maestro timing tables to ensure engine longevity in the face of extreme environmental conditions.

Min and Max octane for adjustable features

The two adjustable tables appear to represent timing for 80(low) and 100(high) octane. Setting the octane slider to some number will cause the ECU to perform a lookup against a (hidden to the user) table which defines the interpolation factor used to determine basic ignition angle. The min and max octane for adjustable features calibration settings are merely used to adjust the window that the slider will operate in. These two settings will not impact the timing interpolation.

Ignition timing, low and high octane

The tables have 3 axis:

  • X axis is Air Mass per stroke
  • Y Axis is Engine speed (RPM)
  • Z axis (the field of cells) is ignition timing

As with any table within Maestro, the X and Y values can be modified to suit the users needs, however the Air Mass and RPM values as set on the base files should satisfy 99.99% of users and are not recommended to be modified.

Setting a Timing Curve

WARNING...DO NOT ADJUST ANY OF THE TIMING VALUES IN THE COLUMNS BELOW 1000MG/STROKE. Why? Daily driving around town from stoplight to stoplight the engine uses ignition timing fairly aggressively due to the lack of airmass (which is due to the lack of exhaust volume spinning the turbine) to power the vehicle. If you lower these values the car will feel sluggish at part throttle. If you increase these values the engine will knock. Only make changes to the last few columns of the tables. Once you get comfortable with tuning and are looking to move to more advanced manipulation (i.e bigger turbo, E85 blend timing, etc..) you may feel the need to increase or decrease values in some of the air mass columns in the 600-900 range. For larger framed/slow spooling turbos you may need to increase timing at low air mass to remove the off/on feeling. Winter gas blends often have less knock resistance that can often lead to excess low air mass/spool knock that one may seek to reduce without also reducing overall timing by adjusting the slider. Use your datalogs to make adjustments as needed. If you are consistently seeing knock in a few cylinders at a specific RPM range then adjust the timing down at that RPM and air mass area. It's best to make timing adjustments to both tables equally (or as equal as possible). If you are going to pull 1 degree of timing out at 6000 rpm in the 1299 air mass column then pull 0.375 from one and 0.75 from the other. If you feel like you need further reductions then pull more from the table that got the 0.375 reduction.

How much KR is too much KR?

This question comes up quite often. The answer is whatever you are most comfortable with. Some people don't want to see any KR. Some people say anything up to -3 degrees in 2 cylinders or less at the same time is ok. Most would agree that -4 or more is not a great idea and one should remedy that. Some cars seem more prone to KR, some have KR at specific RPM ranges that can't be removed with meth or even full E85. You might see one cylinder in particular that has more KR events than the others. Every motor is different. Use your own comfort level when setting timing.

~*~*~*~* Flame 'n' Bang ~*~*~*~*

- To be added by Diggs

Unofficial changelog

Lol