Eurodyne Tables - Revision history

ZuMBLe: /* Basic Lambda vs Airmass DI */

2021-01-27T17:57:04Z

Basic Lambda vs Airmass DI

2021-01-27T17:56:25Z

Basic Lambda vs Airmass DI

2021-01-27T17:24:53Z

Basic Lambda vs Airmass DI

2021-01-27T17:24:01Z

Basic Lambda vs Airmass DI

2021-01-27T17:23:31Z

Basic Lambda vs Airmass DI

2021-01-27T17:23:14Z

Basic Lambda vs Airmass DI

2021-01-12T15:14:53Z

Factory ASW

2021-01-12T15:13:54Z

Factory file

2021-01-12T15:13:18Z

Map for boost pressure actuator setpoint

2021-01-07T03:29:42Z

Timing

@@ Line 13: / Line 13: @@
 This table is the ''part throttle'' fueling map.  The ECU will target the entered lambda values during part throttle (not pedal position).  At full throttle, the ECU will switch to the "Full Load Lambda" fueling table. <br>
-The Airmass DI tables axes are defined INCORRECTLY in Maestro.  When tuning the DI tables, make your changes with the below axes in mind,but do not change the axes values in Maestro:
+The Airmass DI tables axes are defined '''INCORRECTLY''' in Maestro.  When tuning the DI tables, make your changes with the below axes in mind, but do '''not''' change the axes values in Maestro:
 <br>

@@ Line 16: / Line 16: @@
 <br>
-[[File:Screen Shot 2021-01-19 at 9.30.27 PM.png]
+[[File:Screen Shot 2021-01-19 at 9.30.27 PM.png]]
 '''Note:''' "Full Throttle" can happen even if the accelerator pedal is not pushed completely down.

@@ Line 16: / Line 16: @@
 <br>
-[[File:Screen Shot 2021-01-19 at 9.30.27 PM.png|thumb]]
+[[File:Screen Shot 2021-01-19 at 9.30.27 PM.png]
 '''Note:''' "Full Throttle" can happen even if the accelerator pedal is not pushed completely down.

@@ Line 13: / Line 13: @@
 This table is the ''part throttle'' fueling map.  The ECU will target the entered lambda values during part throttle (not pedal position).  At full throttle, the ECU will switch to the "Full Load Lambda" fueling table. <br>
-The Airmass DI tables axes are defined INCORRECTLY in Maestro.  When tuning the DI tables, make your changes with the below axes in mind,but do not change the axes values in Maestro:<br>
+The Airmass DI tables axes are defined INCORRECTLY in Maestro.  When tuning the DI tables, make your changes with the below axes in mind,but do not change the axes values in Maestro:
 [[File:Screen Shot 2021-01-19 at 9.30.27 PM.png|thumb]]

@@ Line 13: / Line 13: @@
 This table is the ''part throttle'' fueling map.  The ECU will target the entered lambda values during part throttle (not pedal position).  At full throttle, the ECU will switch to the "Full Load Lambda" fueling table. <br>
-The Airmass DI tables axes are defined INCORRECTLY in Maestro.  When tuning the DI tables, make your changes with the below axes in mind,but do not change the axes values in Maestro:
+The Airmass DI tables axes are defined INCORRECTLY in Maestro.  When tuning the DI tables, make your changes with the below axes in mind,but do not change the axes values in Maestro:<br>
 [[File:Screen Shot 2021-01-19 at 9.30.27 PM.png|thumb]]

@@ Line 48: / Line 48: @@
 In maestro, the axes are labeled incorrectly.
-The X value is *actually* `fac_2_put_ad`, and the Y value is *actually* `fac_1_put_ad`.
+The X value is *actually* <code>fac_2_put_ad</code>, and the Y value is *actually* <code>fac_1_put_ad</code>.
-Calculating the difference between `fac_pow_put_ctl_opl` and `fac_pow_put_ctl_rgl` will tell you how far off your wgdc table is from your actual wastegate control.
+Calculating the difference between <code>fac_pow_put_ctl_opl</code> and <code>fac_pow_put_ctl_rgl</code> will tell you how far off your wgdc table is from your actual wastegate control.

@@ Line 33: / Line 33: @@
 More commonly known as... wastegate duty cycle.
-==== Factory file ====
+==== Factory ASW ====
 FIRST PASS, NEED MORE DATA TO CONFIRM:
@@ Line 39: / Line 39: @@
 One possible way to tune the wgdc is to measure the following 4 variables:
-```
 fac_1_put_ad - first parameter for precontrol and adaptation
 fac_2_put_ad - second parameter for precontrol and adaptation
 fac_pow_put_ctl_opl - Open loop value of PUT control
 fac_pow_put_ctl_rgl - Regular value for PUT control
-```
+</pre>
 In maestro, the axes are labeled incorrectly.
 The X value is *actually* `fac_2_put_ad`, and the Y value is *actually* `fac_1_put_ad`.

@@ Line 31: / Line 31: @@
 === Map for boost pressure actuator setpoint ===
-More commonly known as... wastegate duty cycle (though it's the reverse).
+More commonly known as... wastegate duty cycle.
 ==== Factory file ====
-TBD
+FIRST PASS, NEED MORE DATA TO CONFIRM:
 [[File:is20_wgdc.png|500px]]

@@ Line 73: / Line 73: @@
 You bang, bang, bang, bang, bang
 Then flame, flame, flame
 You bang, bang, bang, bang, bang
 It's not my thing, so let it go